ketox
-
Posts
14 -
Joined
-
Last visited
-
Days Won
1
Content Type
Profiles
Forums
Gallery
Store
Downloads
Blogs
Events
Articles
Posts posted by ketox
-
-
Yes, I am going to buy Andy's film and see if this is corrected, I have no problem with large and medium prints only with small ones and with care labels.
I am doing tests with a temperature of 200c for 2 min, to rule out if the low temperature of 140c prolonged by 5 minutes is what causes this.
-
I did a test by melting the powder grains with a heat gun and other using an oven as well, but the problem remains ... the small letters come off the film very easily when cutting the labels or handling it. I think the problem is over-temperature, over cured...so it peels off the film easily before putting it on the shirt... Have to do more tests..
-
Not only the printed details, Small typefaces also fall off easily with handling when cutting labels.,
it could be the film, I buy it from china
-
10 minutes ago, johnson4 said:
Hover curing isn’t good enough. The powder needs to melt. Once it’s melted it’s also dry, giving the print a solid backing so it doesn’t do that.
heat gun, flash dryer, belt dryer, etc. your heat press isn’t going to get hot enough, unless you want to hover press it for several minutes or more. It has to hit over 320 degrees or so, dry the ink, then melt the powder. A 1500 degree heat gun takes at least 30 seconds to do the whole print.
Thanks @johnson4,
i am going to do a test with a heat gun, i am having the detach problem with small prints like clothing care labels
-
My mistake , was Hovering for 5 Minutes not 15 Sec.
The Hovering melts very good the powder, all the granules or crystals are melted well and the print gets a glossy finish,
but the small the prints when handling or cleaning with a soft brush, parts of the print fall off the film very easy
-
Hi!, Anyone know why the print after being hover cured at 150c for 15sec.
some parts detach themselves or with little effort from the film?
-
I will continue doing tests, maybe it is the type of DTF paper I will try with another supplier, maybe I will find a thicker paper, for now I will continue printing with the roll
-
2 minutes ago, johnson4 said:
Maybe, I turned all that off. Mine it was the timing was incorrect.
That may be the reason for the problem, Can I adjust the timing with the service program?
-
On 11/14/2020 at 7:16 AM, TiK80 said:
Hey,
how high have you Set the ink limits on AcroRip?
i‘m trying with 20% ink limit cmyk and 20% wwww on the epson p800 and I think there is still a lot of ink on the film...P800 on Acrorip, printing on DTF roll, I use 2 white cartridges only
Settings: Low Ink Drop, 55 % Color and 60 % White, give good results to me on Dark gray cotton
-
3 minutes ago, johnson4 said:
just out of curiosity, did you leave about a 1/4 inch gap between the paper slide guide and the paper?
No gap at all, the slide and the paper (film) are tight
Im think that the error is because the paper arrive with some skew to the front
-
On 11/9/2020 at 8:14 PM, johnson4 said:
Out of curiosity I tried the film that I have, that you probably have. It does do this in my P800 as well. As Andy stated, putting sheets of paper behind it solved it for me ( I put like 20 sheets, because why not). The reason it does this, ( even does it to me sometimes with regular photo paper too, Mainly Matte) is When the ASF is triggered, vs the PE ( paper load) there is a certain "time" that is allowed. If it doesn't hit that mark, it spits it out.
Yes, all rollers cleaned. The DTF paper still spitting it out 1 of 3 times, even with the paper stack. (100 Sheets),
agree with you that is when the ASF is triggered, vs the PE, that like the paper did not arrive on time.
I did a test removing the cn48 Sensor (Paper,Detector,Pe,Asf, Assy) and still the spitting out
I Agree the paper is to thin.
All ok printing on roll..
-
Thanks @johnson4,
Now Im printing on Film Roll, Ek & Acro Ok!.. 👍.
Just The top Feeder still passes the film sheet direct to eject and ask, want to resume or cancel? (works fine with plain paper)
The Front Feeder for Fine Art Paper still displaying wrong media...
-
Hello everyone, a question here
Do you have to do some type of modification or configuration, so that the p800 printer accepts the Pet Film?
here my p800, only passes the film paper through one side to the other when i use the sheet feeder;
and when I use the Film on the roll feeder, displays Error! wrong media.
All these after send to print from Acrorip and Ekprint
Welcome any help, Thanks !
Print detach themselves from the film after curing
in General Direct to Film Discussion
Posted
Long time low temperature was the cause of the problem.