anum11 Posted February 28, 2022 Share Posted February 28, 2022 Hi, I made a dtf xp15000, but when printing on paper carriage strikes paper on where the rollers was. Is there something additional to do, or should i impovise it. I tried to use thick paper setting but did not work. Using acrorip 10.3. any hints would be helpful Quote Link to comment Share on other sites More sharing options...
johnson4 Posted March 1, 2022 Share Posted March 1, 2022 (edited) 5 hours ago, anum11 said: Hi, I made a dtf xp15000, but when printing on paper carriage strikes paper on where the rollers was. Is there something additional to do, or should i impovise it. I tried to use thick paper setting but did not work. Using acrorip 10.3. any hints would be helpful If your output tray is the right height and level it shouldnt do that. Edited March 1, 2022 by johnson4 Quote Link to comment Share on other sites More sharing options...
Chevelle Posted March 1, 2022 Share Posted March 1, 2022 Mine did the same thing when i bought it, I just use a piece of cardboard on top of output try level where the sides of the output tray go up. Quote Link to comment Share on other sites More sharing options...
anum11 Posted March 3, 2022 Author Share Posted March 3, 2022 On 3/2/2022 at 1:31 AM, Chevelle said: Mine did the same thing when i bought it, I just use a piece of cardboard on top of output try level where the sides of the output tray go up. Can you put a picture here, i did not understand what you meant well enough. Quote Link to comment Share on other sites More sharing options...
johnson4 Posted March 3, 2022 Share Posted March 3, 2022 2 hours ago, anum11 said: Can you put a picture here, i did not understand what you meant well enough. The original output tray- he put cardboard on it to to make it taller and flat and support the whole sheet. Quote Link to comment Share on other sites More sharing options...
anum11 Posted March 4, 2022 Author Share Posted March 4, 2022 19 hours ago, johnson4 said: The original output tray- he put cardboard on it to to make it taller and flat and support the whole sheet. Printhead goes to paper too close. I removed whole wheel assambly, was that supporting to other Side of carriage? Because it seems like one side of carriage drops down after leaving cap and because of that there is literally no space between. I closed Epson monitor too. I am trying to adjust printer for thick paper but it does not do anything diffirent. Quote Link to comment Share on other sites More sharing options...
anum11 Posted March 4, 2022 Author Share Posted March 4, 2022 Update issue was about acrorip 10.3, with it printhead was not moving up before printing. Therefore it was striking paper nomatter what. Quote Link to comment Share on other sites More sharing options...
anum11 Posted March 4, 2022 Author Share Posted March 4, 2022 Also my catridge levels never goes lower with chipless software btw. Quote Link to comment Share on other sites More sharing options...
johnson4 Posted March 5, 2022 Share Posted March 5, 2022 6 hours ago, anum11 said: Update issue was about acrorip 10.3, with it printhead was not moving up before printing. Therefore it was striking paper nomatter what. Wait, your printhead moves up and down on the 15000? Quote Link to comment Share on other sites More sharing options...
johnson4 Posted March 5, 2022 Share Posted March 5, 2022 (edited) 5 hours ago, anum11 said: Also my catridge levels never goes lower with chipless software btw. That’s awesome, that was my biggest issue with the 15000, I mean aside from the crappy aftermarket carts. it has been awhile now though since I’ve used one. i still have a new one here. I plan on trying acro 11 when it comes out. Edited March 5, 2022 by johnson4 Quote Link to comment Share on other sites More sharing options...
anum11 Posted March 5, 2022 Author Share Posted March 5, 2022 (edited) 11 hours ago, johnson4 said: That’s awesome, that was my biggest issue with the 15000, I mean aside from the crappy aftermarket carts. it has been awhile now though since I’ve used one. i still have a new one here. I plan on trying acro 11 when it comes out. False alert, catridge counts goes down, but my ink and film was good so i was using too little ink. Now tried with full settings it goes down to empty around 120-150cm. However yes, printhead moves up before printing starts, it waits before feeding paper and adjust it. I opened the setting in driver. On acrorip 10.3 setting does not work, so printhead strikes nomatter what. With this setting it barely does not touch the film at full ink settings. Any minor mistake it will strike the film again. However once it is adjusted on auto shaker, it wont strike at all with thick paper setting. I use 720*720 resolution, so print speed and quality is also good. Edited March 5, 2022 by anum11 Quote Link to comment Share on other sites More sharing options...
johnson4 Posted March 5, 2022 Share Posted March 5, 2022 7 hours ago, anum11 said: False alert, catridge counts goes down, but my ink and film was good so i was using too little ink. Now tried with full settings it goes down to empty around 120-150cm. However yes, printhead moves up before printing starts, it waits before feeding paper and adjust it. I opened the setting in driver. On acrorip 10.3 setting does not work, so printhead strikes nomatter what. With this setting it barely does not touch the film at full ink settings. Any minor mistake it will strike the film again. However once it is adjusted on auto shaker, it wont strike at all with thick paper setting. I use 720*720 resolution, so print speed and quality is also good. Yea, it’sa good fast printer especially for the price as long as you keep from wetting the head electronics. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.