Mr.Carter

On 7/4/2023 at 10:23 PM, tangkibot said:

Does the APG sensor have to be connected too? 

No its not connected 

Looks great , nice job

Those who really want to purchase the code contact me on email my id is mr.charter1400@gmail.com

You can use digital factory v10

Those who really want to purchase they can email me ,  code is not available for sale board price 300$ including wiring,motors etc

except uv lamp please note

mr.charter1400@gmail.com

On 3/16/2023 at 2:11 PM, N1ko88 said:

 

Yes

Problem is with your white in circulation system, try to keep it off and then print

Here is my setup

On 12/23/2022 at 11:31 AM, Mr.Carter said:

So if anyone want to convert XP-15000 to industrial roll to roll machine same as xp600 chinese printer i have conversion kit available(currently only for USA)

what you will get

1.Controll board to emulate all the sensor

2.pump assembly for ACSAP autoclean system after each print to get very accurate prints everytime

3.touch screen controll display

4.smps 12v to power the board

 

Features of Controll board

1.auto ink reset(chipless firmware is required) printer will not show your carts runout after few print which is the bug of chipless firmware 

2.supports roll and sheets as well just need to change mode from display 

3.can do headclean when the roll is loaded inside the printer it will not eject it out

4.12v port for auto roll unwinding and sensor

5.cut media feature for roll printing 

6.load media feature to load the sheet inside

7.foward backward buttons on display to move media forward or backwards 

8.setting can be adjusted from display like cut distance , move speed etc. To align it with your setup

9.timer 12v port for white ink stirrer motor

How to install 

Installation is very easy remove the side lead of printer so you can access motherboard connectors just remove the original cables and plug cables coming out from control board

 

Price 300$

250ml Bulk in system with wims addon +150$

1 hour ago, overprint said:

Do I need a separate part to make it?

Please check the above msg

15 minutes ago, Jimmy Stanley said:

my inline dampers don't fit in the rubber boot tight, so im going to get creative.

It didn't fit very strongly you can use some super glue at the edges

6 hours ago, Jimmy Stanley said:

Can you show me a picture of your finished setup with theseand how you have it setup with gravity feeding? also, are you sealing the inline dampers to the aftermarket cartridges or do they just plug into the little rubber boot thet the piplines normally plug into?

Just plug into that rubber boot adding a bit of superglue will make it more durable 

Gravity feed system means keep the ink above the cartridge level so inks stay present always till the inlet of the damper 

In short make a siphon flow

We can discuss here btw

On 12/26/2022 at 2:03 AM, Rohitb said:

this Work For L8180 OR ET 8550?

Nope

This is must note it down..

So if anyone want to convert XP-15000 to industrial roll to roll machine same as xp600 chinese printer i have conversion kit available(currently only for USA)

what you will get

1.Controll board to emulate all the sensor

2.pump assembly for ACSAP autoclean system after each print to get very accurate prints everytime

3.touch screen controll display

4.smps 12v to power the board

Features of Controll board

1.auto ink reset(chipless firmware is required) printer will not show your carts runout after few print which is the bug of chipless firmware 

2.supports roll and sheets as well just need to change mode from display 

3.can do headclean when the roll is loaded inside the printer it will not eject it out

4.12v port for auto roll unwinding and sensor

5.cut media feature for roll printing 

6.load media feature to load the sheet inside

7.foward backward buttons on display to move media forward or backwards 

8.setting can be adjusted from display like cut distance , move speed etc. To align it with your setup

9.timer 12v port for white ink stirrer motor

How to install 

Installation is very easy remove the side lead of printer so you can access motherboard connectors just remove the original cables and plug cables coming out from control board

Price 300$

250ml Bulk in system with wims addon +150$

On 12/21/2022 at 8:39 PM, AMartinez said:

Thank you guys for the tips, I didn't give up lol and I finally got good prints with 35 ink/75 white and mix drops, the color seemed a bit light still, so I will tweak a little more, but it's 90% of the way there now.

Acrorip gives best prints on medium+large dot size

20 minutes ago, AMartinez said:

Anyone with success, care to share their certified settings for this combo.  While I love the user interface and the color reproduction of acrorip over EKprint, I spent a full day yesterday, burning through ink and film searching for the perfect settings using custom ink settings, and all ink settings, 720 vs 1440, mix vs med vs med+lrg drops, and mostly I got thin prints that couldn't fully cover up the color of the t shirt (white base prints), and when I finally got thick white base that should have been capable using 30-40% color/80% white, after cure the print was FULL of pin holes and the print became almost completely see through when held up to the light, I never experienced this with EKprint, and nothing has changed except the software, same printer, ink, powder, film, etc.

And just to make sure I then used the same image into ekprint just to make sure I didn't screw something up, and it came out perfect just like I'm use to.

Happens when you have too much white ink more than required and fast curing of the film always bake the film at low temperature with more time 2-3mins

15 minutes ago, johnson4 said:

Nice, that’s a lot of film. Are you using the aftermarket carts with inline damper on this one? 

Yep

After doing this you are ready to go into dtf with your cheap dtf printing guy

i have printed 30Rolls still working no printhead replacement yet

Why to go for hardwork this is simple solution 

Second thing is make your printer little bit tilted by adding 2x1inch wood block at the back side of the printer

Like this. so that even if there is 1 or 2 drop of leak during cartridge installation ink will not go towards headcable area it will get drip off from front side of the carriage 

On 10/23/2022 at 8:11 PM, rohaddaughgs said:

Hello @8308MrCarter I believe you are the person im looking for, i have an A4 l805 uv printer i bought, and unfortunately short circuited the main board. i just bought the replacement ce86 main board, but i cant get the printhead to move and may not have rewired it to board correctly. f you wouldnt mind sharing your knowledge with me and any wiring diagrams etc so i can get it working once again i would be very greatful. I also understand that your time and effort are not free and ill compensate you the requested amount as well. here is my email address to let me know where to send my contribution to you and you can bless me with the files. thank you once again for your efforts and i appreciate you! 

rohaddaughgs@gmail.com

The code sent already if it will help you in some way then only pay me

I check the cartridges i recived and compared it OEM i noticed that the pads are slightly shifted on aftermarket carts.

Removed the chip installed it at correct position according to my judgment now it is showing this the error is changed

9 hours ago, anum11 said:

Printers usually would error if you dont make initial charge original catridges that came in package. 
 

Try to first charge with original catridge chips then change into resetable ones.

I can try that but i dont have all the OEM carts available to me LLK cartridge is missing to try this i have to purchase the LLK cartridge 

Another thing is if i will run initial charge with OEM , the OEM ink will go inside the printer and all the ink system and that is what i want to avoid as i will be using it for dtf

6 hours ago, johnson4 said:

Could be. They should be 200ML carts and chips. I have about 10 sets of chips and every now and again one won’t reset, but nothing like you are experiencing. 
 

is also possible to use OEM chips. I did at first as well to make sure if they didn’t reset the Chinese chips. 
 

Messy work, but I removed ink sensor from ink bag( old R4900 empty cart sensors will work on them too), solder to backside of oem chip and sealed the sensor with ink on it so it would always read “ full” or not empty. After first reset it says non genuine, but also worked. 
 

I did that as backup method but haven’t needed to use them for that reason. 

Did you mean OEM carts has sensor inside them and we can just bypass the sensor and it will always read full? No need to reset chips?